Pat, wa0tda, wearing FT8 - ham radio without the jibber jabber t-shirt & giving a thumbs up

Pat, WA0TDA

As  winter is on our doorstep there are fewer thunderstorm outages.  There are better band conditions on 160, 80, and 40 meters, thanks to less daylight and correspondingly less D layer absorption in the ionosphere.

Old News:  W0EQO is back in service after upgrades to the shack & internet completed.  In the photo on the left, you can see the rig control laptop and the Icom IC-7300.  The RCForb host software is running on the PC.  The Yaesu FT-897 is used for in-the-shack communication and is not available as a remote controlled radio.   In the photo on the right, you can see the new Netgear router and the uninterruptible power supply (installed on 5 August 2022), as well as the new wooden shelf built by Bill, N0CIC, that makes having the UPS available to power the router possible in the limited space we have.

ALL STATIONS ARE SUBJECT TO UNANNOUNCED THUNDERSTORM OUTAGES. 

Thunderstorms can happen year around in Minnesota.  There may be sporadic outages at WA0TDA & W0ZSW as the antennas will be disconnected to prevent lightning damage to the stations.   You can check out the lightning map at: https://www.blitzortung.org/en/live_lightning_maps.php?map=30

Once the danger of lightning is past, the stations will be returned to service.

Old news: 

WA0TDA has returned to service after an outage.  The WA0TDA IC-7200 had suffered a receiver failure, and the station was off the air.  An Icom IC-7300 has replaced the old radio.

W0ZSW was offline on November 12 due to the failure of a power supply feeding a network switch, thus causing a loss of internet to the host PC.  Please be sure to let me know when something isn’t working, as I don’t always notice these kinds of failures if the stations have been checked early in the day and found to be working.  I can be contacted at wa0tda@arrl.net.  Thanks!

W0EQO Update:  Station W0EQO is now in rural Park Rapids, MN.  This location in the North Woods is not far from the headwaters of the Mississippi and has a low noise floor. It is operating at 60 watts periodically due to a problem with RF in the shack.  Digital mode operation is NOT allowed as this is likely to trigger the RF problem and cause a loss of internet control.  SSB/CW should be okay.  We are considering ways to address the RF problem.  It is worst on 40 m, so no 40 meter operations are allowed at this time.

Both Twin Cities stations are subject to intermittent outages because of thunderstorm activity.  Antennas will be disconnected to protect the equipment. 

Software interface radio

    1. New RCForb software

Use the latest version 0.9x software or it will not work on Windows!  Download the new client software to use the remotes here.

Dear HF Operator:

Welcome to the HF Remotes!  This website has information on the following
stations:

W0EQO – Northern Minnesota in the tall pine forest near the headwaters of the Mississippi; Icom IC-7300 radio equipped with speech readout feeding a 300 foot dipole antenna fed with 450 ohm ladder line and a current
balun.  160 through 6 meter operation. Grid square is EN27mc in Hubbard County, MN USA. Callsign admin is WA0TDA.  Station hardware admins are N0CIC & WA0TDA.

W0ZSW – Metro Minnesota Twin Cities location at WA0TDA QTH; Icom IC-7300 radio feeding an off-center fed dipole antenna.  80 through 6 meter operation.  Grid square is EN34mw in Washington County, MN USA. Callsign admin is KA0PQW.  Station hardware admin is WA0TDA.

WA0TDA – Metro Minnesota Twin Cities location at WA0TDA QTH; Icom IC-7300 radio feeding an inverted vee maypole antenna system fed with underground coax. 160 through 6 meter operation. Grid square is EN34mw in Washington County, MN USA.  Callsign & hardware admin is WA0TDA.

All of the above stations can run up to 100 watts and all are SSB and CW capable. All are subject to occasional maintenance outages or weather outages.

Please contact wa0tda@arrl.net to report a problem with any of them.

The quick start guide is for anyone who wants to install and use the RCFORB HF remote base client software from Remotehams.com with a minimum of time and effort. That would be most of us! A quick start guide shouldn’t be
wordy, so let’s just use some simple steps to get you up and running.

IMPORTANT:  Register with Remotehams.com using YOUR CALLSIGN as the username, or this will not work!

Get the WA0TDA RCFORB Quick Start Guide in PDF:
http://tice.us/wa0tda/wp-content/uploads/2016/04/The-WA0TDA-RCFORB-Quick-Start-Guide.pdf
Note:  Always choose the newest version 0.9 version of the client software, NOT the version 0.8 as is recommended in the guide or video.  The old 0.8 version will be deprecated due to the removal of Adobe Flash support in Windows.

Screenshot of download page

Choose ONLY 0.9 software!

I have made two YouTube videos on the use of the RCForb software.  This one
is for the free Windows version:
https://youtu.be/V3Sw2aC6Gcs

Note:  Always choose the newest version 0.9 version of the client software, NOT the version 0.8 as is recommended in the video.  The old 0.8 version will be deprecated due to the removal of Adobe Flash support in Windows.

This one is for the Android version, which you can buy from the Play Store for under $10:
https://youtu.be/1zZOK34pj9M

If you are a blind user, be sure to check out the K8HSY guide:
http://handiham.net/index.php/2016/08/02/remotehams-users-manual-for-blind-hams/

The Handiham Radio Club also has a useful website:
http://handiham.net/

Good luck and have fun with the radios!

73,

Patrick Tice
wa0tda@arrl.net

Attachments area

Preview YouTube video Handiham Remote Base HF Stations

Preview YouTube video Ham radio with your smartphone! RCForb Android App Explained